What should I do if I encounter a water pipe leak? How to repair and deal with?

In daily life, water pipe leakage is a relatively common problem, when unexpectedly encounter water pipe burst, in order to avoid greater losses, should be in the master repair before, do a good job of emergency treatment, to avoid the constant accumulation of water flow of the water pipe, resulting in furniture is wet, over time will be moldy, that water pipe leakage how to do? How to repair and deal with? Here's a look at it.

A. How to do about water pipe leaks?

1, if it is a PVC water pipe, you can buy a PVC water pipe yourself connected, first cut off a bad one, the interface first set into one end of the pipe, so that the other end is cut just flush with the other bite of the interface, so that it is just straight, and then sent directly to this end, so that the two ends have a certain cross distance (length), and then disassemble. Apply PVC glue on the inside of both ends of the straight pipe and the outside of the two downpipes.

2、You can buy waterproof tape to repair the downpipe, wrap the line, and then use mortar waterproofing agent and cement to apply on the line.

3, find a professional company is better, you can not get.

B. What about iron pipe leaks?

Iron water pipe leaks, according to different situations using different methods

1, 2 cm diameter iron water pipe leaks but the iron water pipe is not embroidered, only part of the location of damage, the main valve to close the water pipe, just need to replace the location of the iron water pipe! Cut the location of the water pipe, in the use of appliances with wire cut wire buckle, in the curb connection head can be!

2, 2 cm diameter iron water pipe leakage, because the overall corrosion of the water pipe, close the main valve of the water pipe, the section of the water pipe as a whole to replace the pin screwed on both ends

3, 20 cm diameter iron water pipe leakage, if the problem is the connector replacement joint section. If the body of the pipe leaks, polishing embroidery system original body, in the use of welding methods to repair attention needs to be inlaid in the location of repair and water pipe iron plate closely fit to do reinforcement treatment.

C, PPR plastic water pipe leakage how to do?

1、First use a small hacksaw to saw off the leak - the sawing mouth should be flat.

2、Gently polish the newly exposed port with sandpaper, not too much.

3、Wipe the port clean with a clean cloth.

4、Use special glue on the port and let it dry for a while; apply glue while the "bamboo" joint is still there.

5、Connect the port with the "bamboo", turn it repeatedly until it is firm. Connect the other end in the same way.

6, after all OK in the seam to apply the right amount of glue to ensure that no leakage.

D、What about leaking water pipe joints?

Besides new ones, what is the best way to replace a leaking water pipe joint at home? The pipe joint itself is bad, can only be replaced with a new one; round corner leaks can be removed, such as no gasket installation gasket, gasket aging for a new one, round corner coated with thick white paint, installed with hemp wire wrapped, raw material tape winding the same. If it is the glue or fuse at the leak is more difficult to solve themselves.

E, water pipes leak in the wall how to do?

Water pipe leaks in the wall, you can only chisel the wall, in order to really find the leak of the water pipe and repair it completely. In addition, you can also find the property or renovation company to see what the situation is.

These are the five solutions to water pipe leaks, which can basically solve some small problems of daily life plumbing.

Pipe leaks can be used pqwt pipe leak detector, in general, the basic detection method is, connect the pipe leak detector host, headphones, sensors. Turn on the switch, put on the headset, place the sensor on the road above the pipe line, place it step by step according to the length of the pace, step by step to measure and listen, the closer to the leak, the stronger the signal, the farther away from the leak the weaker the signal, by comparing the signal strength between different points to detect the leak. Therefore, we use the pipeline leak detector, a single point in the leak signal is not meaningful, to repeatedly compare multiple points, compare the sound vibration of the larger place is the leak, of course, we have to consider many other additional factors, such as the direction of the leak breakage mouth, because the pipe is round, if the side of the leak, the larger point may instead be on the side of the road above the pipe, rather than The road above the pipeline, so the location of the pipeline should be known, in addition to the tee, bend, water pressure, burial depth, buried layer, etc. will have an impact, the detection should take these into account.

Hunan Puchi Geological Exploration Equipment Research Institute is a professional institution engaged in pipeline leak detection equipment and urban pipeline loss reduction research. Mainly committed to the underground pressure pipeline leak detector application technology research and scientific research and undertake the "National Thirteenth Five-Year Water Special Research Project". Our institute insists on the strategic goal of "developing the institute with science and technology and strengthening the institute with talents", and implements the policy of running the institute in an open manner, and the independent core leak detection technology in the field of research and development of new generation underground pressure pipeline leak detection equipment has attracted great attention in the industry. advantages.